People's life is getting better and better. So people no longer care about whether they can eat enough, but how they can make themselves live in a clean and environmentally-friendly environment, so people's requirements for door selection in decoration are also high.

现在最受消费者认可的就是实木复合门，那实木复合门安装如何进行呢？跟着门业视界小编一起来看看吧!希望对你有帮助。

Now the most popular is the solid wood composite door, and how does the solid wood composite door be installed? Follow the door industry view and look at it. I hope it will help you.

实木复合门安装步骤详解

Detailed explanation of the installation steps of solid wood composite doors

▼

You

1、根据设计图纸检查门的规格、开启方向、相关配件等。

1, according to the design drawings, check the specifications of the door, the opening direction, related accessories and so on.

2、用卷尺量门洞的高与宽。门的标准高宽尺寸是200cm×80cm;的门高宽是200cm×70cm。尺寸如有出入要及时纠正。

2, using tape it high and wide. The standard width of the gate is 200cm x 80cm; the gate width is 200cm x 70cm. If the size is in or out, it should be corrected in time.

3、测量位置线，确定门框的位置，用墨斗弹拉出垂直线，一侧门洞两条垂直线。

3, to measure the position of line, make sure the location, with the fountain playing out the vertical line, one side of the two vertical lines.

4、在垂直线上用冲击钻打眼，孔眼与孔眼之间的距离约为30cm，一侧门两排共10个孔眼。冲击钻的钻头应为12mm，所钻孔眼深度约为6cm。

4, in line with the impact of vertical drilling, hole and hole between the distance is about 30cm, a total of 10 holes in one side of the door two row. The drill bit should be 12mm, and the depth of the hole is about 6cm.

5、将小木楔用铁锤逐个钉入孔眼，以便固定门框板。小木楔的体积大小为5cm×1.5cm×1.5cm，以落叶松制作的为好，因为落叶松的木质结构紧，不容易松动。

5, the small wedge with a hammer by the nail into the hole, so that the fixed frame plate. The size of small wedge is 5cm * 1.5cm * 1.5cm, to make the larch as well, because the wooden structure of larch is tight, not easy to loose.

6、开料制作门框。

6. Open the door frame.

左右做两侧门框龙骨的木工板尺寸为200cm×3cm×8cm，门框顶龙骨的木工板尺寸为80cm×3cm×8cm。将高密度九厘板涂胶粘在龙骨上，再用汽枪钉固定。专业好文，尽在门业视界。

The size of the woodworking board on both sides of the door frame keel is 200cm * 3cm x 8cm, and the size of the woodworking board of the door frame top keel is 80cm * 3cm * 8cm. The high density nine board coating adhesive on the keel, with all screws. Good professional, all in the industry view.

7、将制作好的三条门框按门的形状连接起来，并且用大钉子在接合处固定。

7, the three door frames are connected in the shape of the door, and a large nail is used to fix the joint at the joint.

8、用刨子将连接好的门框表面修平整，修整边角，棱角分明。

8, with a door surface repair will connect good leveling, trimming angle, angular.

9、将门框放到门洞上，按墙面的水平线为准，门框下拿木头或者砖头垫起，调节门框的高度。下面预留5cm埋在地板的龙骨中。

9, the door into the doorway on the line, according to the level of the wall is next door, take the wood or brick pad, doorwww.fangzhuangmj.cnwww.gaibanmojuz.cn www.huludaobanjia.cn www.haimianji.cn www.huludaoyanglao.cn www.diandongmena.com.cn height adjustment. Next, 5cm is reserved in the keel buried in the floor.

10、在门框的上面钉一个钉子，把线垂挂上，通过线垂来调整门框的垂直，一边衡量一边用麻花钉将门框固定在门洞上。

10, in the frame above the nail a nail, hanging on the line, the line to adjust the vertical vertical frame, side side of the door frame is fixed in a measure of nail openings with a twist.

11、制作门脸的线条。门脸可以是现成买的，也可以是施工人员按照图纸做出来的。制作完成后，就把门脸固定到门框上六，这样门套就基本完成了。专业好文，尽在门业视界。

11, making front lines. You can buy ready-made Menlian, can also be done in accordance with the drawings and construction personnel. The production is completed, the front fixed to the frame six, the door basically completed. Good professional, all in the industry view.

12、把门放到门套上比划好，确定合页在门套上的具体位置，再按合页的厚度切出口径。也切出锁套的口径。将门安装到门套上，合页用锣丝刀将锣丝钉拧紧。注意门与门套的间隙不得大于1.5mm，以顺畅开关门为准。

12, the door to door gestures, to determine the specific location of the hinge on the door pocket, then press the hinge of the thickness of cut diameter. The bore of the lock is also cut out. The door is mounted to the door hinge screw knife will screw nail tighten. Pay attention to the gap of the door with the door not greater than 1.5mm, to smooth opening and closing prevail.

13、清除门套表面的附着物及灰尘赃物，然后涂腻子。在涂腻子前先在门脸与墙面之间贴上美文纸，防止喷涂油漆时沾到墙面上。涂腻子时一定要均匀，修补好门套上钉眼。

13, remove door surface attachment and dust dirt, then apply putty. In the putty before and on his wall between the front paper, prevent the spray paint stick to the wall. Putty must be uniform, repair the door nail in the eye.

14、喷涂油漆。油漆喷涂效果会更加细腻一点，而细部可用刷子涂刷。

14. Spray paint. The effect of paint spraying will be more delicate, and the details can be brushed with brushes.

15、将锁安装到锁孔上，小心不要弄坏油漆。

15. Install the lock on the lock hole, be careful not to break the paint.